Car Wheels
VR
  • Product Details
PRODUCT DETAILS
      

PRODUCT PARAMETERS
      


ModelSizeOffset(mm)PCD(mm)Center hole CB(mm)Color Weight(KG)
J086-1314x443100*4H64/67MGM21AP/MC/GM224.36
J086-1414x4.543100*4H67/64.U29/MC/.GM22/MGM21AP4.46
14x5.543/50100*4H64/67MGM21AP/GM22/MC4.74
J086-1515x4.543100*4H64/67.GM22/MGM21AP/MC/.U294.9
15x643/45/5398-100*4H/5H54-73.1MGM21AP/.U29/MC/.GM20/.GM225.8
J086-1616x545100*4H64/67MGM21AP/GM20/U295.96
16x6.538/48/53100-114.3*4H/5H64-73.GM22/MC/MGM21AP/.U297
16x740100-115*4H/5H67.1/72.64MCAP/MC/H7.1
J086-1717x738-55100-115*4H/5H56.62-73.1MA/MC/MGM21AP/.U29/.GM22/.GM20/MCAR/.GM20/.C8.15
J086-1818x7.538-55100-114.3*4H/5H64-73.1MC/.U29/MGM21AP/.GM228.54
18x8.530/35/45114.3*5H73MC/MGM21AP/U29/GM20/GM229.16


Describe
      

  Production process 

  Low-pressure casting wheels


  Custom Products 

  13-18 inch multi-size, multi-colour, rich parameter style


   Material 

   Made in A356 aluminum alloy

   

    Color 

    Bronze, high gloss black, gunmetal grey, silver, blue


    Surface Process

    Fully coated process


    Design Features

    Classic multi-spoke lightweight design with a variety of product parameters to suit a wide range of sizes from fine to large.













Color Matching


                 
                 

Polish:

Gross Black

Polish:

Matte Black

Polish:

Flash Silver Gun Metal

Polish:

Tanzannian sapphire blue

Polish:

Gross Bronze

Brush:

Candy Red Clear Coat

Brush:

Brown Clear Coat

Brush:

Blue Clear Coat

Brush:

Bronze Clear Coat

Brush:

Blue Black Clear Coat

Testing facility
       
1 Harmonic detection

Full automatic wheel run out/dynamic balance testing line, suitable for wheel run out and dynamic balance detection.

Run out test: measure the size and phase of the inner and outer radial and axial run out of the wheel.

Dynamic balance test: measure the size and phase of unbalance on both sides.

       
2 Impact test

  The lower the flat ratio of the tire, the higher the standard of impact resistance of the wheel. The lower the flat ratio, the greater the impact of the road towards the rim. In response to these changes, JWHEEL uses 30°and 13° impact tests to measure the wheel. (That is, radial impact test is to strike the barrel with a certain hammer weight ).

 

  The 13° impact test mainly uses a heavy hammer to impact the part where the wheel edge connected with the tire at an Angle of 13°, so as to simulate the impact that the car may go through while running on the road, for example rocks or the edge of the road. There are two criteria to measure whether the wheel should be accepted : Spokes should not have penetrating cracks, and the tire should not be completely separated from the barrel within 30 seconds.


       
3 Salt spray test

Salt spray test is a test that examines the corrosion resistance of the products or metal materials. It uses a salt spray test equipment that creates salt spray environment conditions to detect whether the coating of the wheel is stable, and will there be paint drop, electroplating fade, or cracking, etc.


       
4 Helium detection

  Helium mass spectrometer is used to detect the leakage of the hub. Helium gas is used as the tracer gas. Different masses of gas will be separated according to the mass charge ratio in the mass spectrometry chamber of the mass spectrometer. Then the mass spectrogram of the tracer gas can be obtained, and the hub leakage rate can also be obtained safely, quantitatively and quickly.


       
5 Air tightness test

  Water tightness test - bubble leak detection method. Its detection principle is to close the inner and outer side of the aluminum alloy wheel with sealing disk through external force, and then immerse the wheel and sealing disk in water, as the aluminum alloy wheel is closed, a part of the gas is compressed, resulting in the increase of the pressure of the inner cavity of the wheel. If the wheel rim has a leak hole, the compressed gas will leak out from the leak hole and form bubbles in the water.


       
6 The X-ray detection

No matter what kind of manufacturing method is applied, we can not completely avoid the defects that may be created during the production process. JWHEEL company will find out any unqualified hubs by X-ray detection and then do the recasting. Only 100% good hubs will be moved into the next production process. 

The wheel, as a high-speed moving and weight support part of a vehicle, has a vital relation with the safety performance of the whole vehicle and the safety of drivers and passengers. Therefore Jwheel attaches great importance to the hub quality.

 There are a series of reasons that may cause casting wheel defects. Such as not strict enough raw material control, unreasonable production process, unreasonable mold structure design, etc. Casting defects includes bubbles, pores, inclusions and looseness, etc. As the internal defects cannot be identified by naked eyes, X-ray becomes a good way to detect the internal quality of the wheel.


       
7 Bending test

  Bending test is to determine the solidity of the rim and spoke by simulating the stress on the wheel when the vehicle is shaking. The whole wheel is subjected to a rotational bending force. The load of the wheel in the test varies from 500 kg to 720 kg depending on the wheel parameters, and the number of rotations is not less than 100,000 revolutions according to industry standards. For the appearance of any of the following three phenomena, the test will be determined failed. (1) the wheel can not continue to bear the load (2) New visible cracks appear in any part of the wheel (3) Before reaching the required number of cycles, the offset of the loading point has exceeded 10% of the initial loading.


       
8 Radial fatigue test

  The radial fatigue test simulates road conditions while driving. Install the hub to the tire to run for 500,000 or even 1,000,000 rotations on the test platform.








Basic Information
  • Year Established
    --
  • Business Type
    --
  • Country / Region
    --
  • Main Industry
    --
  • Main Products
    --
  • Enterprise Legal Person
    --
  • Total Employees
    --
  • Annual Output Value
    --
  • Export Market
    --
  • Cooperated Customers
    --

Recommended

Send your inquiry

Leave A Message

The first thing we do is meeting with our clients and talk through their goals on a future project.
During this meeting, feel free to communicate your ideas and ask lots of questions.
Recommended
They are all manufactured according to the strictest international standards. Our products have received favor from both domestic and foreign markets.
They are now widely exporting to 500 countries.
Chat with Us

Send your inquiry

Choose a different language
English
ภาษาไทย
Nederlands
हिन्दी
한국어
日本語
العربية
Português
italiano
русский
français
Deutsch
Español
简体中文
Türkçe
Current language:English