Casting Wheels
  • Product Details


ModelSizeOffset(mm)PCD(mm)Center hole CB(mm)Color Weight(KG)
J257-1818x845 120*5H72.6MIC11.2
19x9.545 120*5H73MIC11.98


  Production process 

  Low-pressure casting wheels

  Custom Products 

  For Japanese, American and German vehicles


   Made in A356 aluminum alloy



    high gloss black

    Surface Process

    Facing process

    Design Features

    Five-petal style with some surfaces more stylized and suitable for female users

Testing facility
1 Harmonic detection

Full automatic wheel run out/dynamic balance testing line, suitable for wheel run out and dynamic balance detection.

Run out test: measure the size and phase of the inner and outer radial and axial run out of the wheel.

Dynamic balance test: measure the size and phase of unbalance on both sides.

2 Impact test

  The lower the flat ratio of the tire, the higher the standard of impact resistance of the wheel. The lower the flat ratio, the greater the impact of the road towards the rim. In response to these changes, JWHEEL uses 30°and 13° impact tests to measure the wheel. (That is, radial impact test is to strike the barrel with a certain hammer weight ).


  The 13° impact test mainly uses a heavy hammer to impact the part where the wheel edge connected with the tire at an Angle of 13°, so as to simulate the impact that the car may go through while running on the road, for example rocks or the edge of the road. There are two criteria to measure whether the wheel should be accepted : Spokes should not have penetrating cracks, and the tire should not be completely separated from the barrel within 30 seconds.

3 Salt spray test

Salt spray test is a test that examines the corrosion resistance of the products or metal materials. It uses a salt spray test equipment that creates salt spray environment conditions to detect whether the coating of the wheel is stable, and will there be paint drop, electroplating fade, or cracking, etc.

4 Helium detection

  Helium mass spectrometer is used to detect the leakage of the hub. Helium gas is used as the tracer gas. Different masses of gas will be separated according to the mass charge ratio in the mass spectrometry chamber of the mass spectrometer. Then the mass spectrogram of the tracer gas can be obtained, and the hub leakage rate can also be obtained safely, quantitatively and quickly.

5 Air tightness test

  Water tightness test - bubble leak detection method. Its detection principle is to close the inner and outer side of the aluminum alloy wheel with sealing disk through external force, and then immerse the wheel and sealing disk in water, as the aluminum alloy wheel is closed, a part of the gas is compressed, resulting in the increase of the pressure of the inner cavity of the wheel. If the wheel rim has a leak hole, the compressed gas will leak out from the leak hole and form bubbles in the water.

6 The X-ray detection

No matter what kind of manufacturing method is applied, we can not completely avoid the defects that may be created during the production process. JWHEEL company will find out any unqualified hubs by X-ray detection and then do the recasting. Only 100% good hubs will be moved into the next production process. 

The wheel, as a high-speed moving and weight support part of a vehicle, has a vital relation with the safety performance of the whole vehicle and the safety of drivers and passengers. Therefore Jwheel attaches great importance to the hub quality.

 There are a series of reasons that may cause casting wheel defects. Such as not strict enough raw material control, unreasonable production process, unreasonable mold structure design, etc. Casting defects includes bubbles, pores, inclusions and looseness, etc. As the internal defects cannot be identified by naked eyes, X-ray becomes a good way to detect the internal quality of the wheel.

7 Bending test

  Bending test is to determine the solidity of the rim and spoke by simulating the stress on the wheel when the vehicle is shaking. The whole wheel is subjected to a rotational bending force. The load of the wheel in the test varies from 500 kg to 720 kg depending on the wheel parameters, and the number of rotations is not less than 100,000 revolutions according to industry standards. For the appearance of any of the following three phenomena, the test will be determined failed. (1) the wheel can not continue to bear the load (2) New visible cracks appear in any part of the wheel (3) Before reaching the required number of cycles, the offset of the loading point has exceeded 10% of the initial loading.

8 Radial fatigue test

  The radial fatigue test simulates road conditions while driving. Install the hub to the tire to run for 500,000 or even 1,000,000 rotations on the test platform.

Exhibition display


  • Q1: How to gurantee the wheel quality?
    A:All of our products conform to the JWL/VIA standard, undergo rigorous impact test, cornering fatigue test, radial fatigue test ; Our factory is ISO/TS16949, ISO14001 TUV SFI JWL/VIA certified.
  • Q2: How about your delivery time?
    A:From the deposit received date, we will finish production within 35-45 days. If the wheel mould is needed, it will takes 3-4 weeks longer.
  • Q3: What information should I provide for a quotation?
    A:Usually we need to know : car model and the wheel size , PCD , CB , ET(offset) ,color and order quantity to make a correct quoation for you.
  • Q4: Do you accept OEM or ODM order?
    We accept OEM, ODM with customer's logo, wheel design and packing design.
  • Q5: What's your MOQ?
    A:For our existing mould of casting wheel, MOQ is 100pcs/size/fitment, with 2 colors. if you want to make your own design, we can discuss about the MOQ. For the forged wheel, no need to open mould for new design, MOQ is 4pcs.�
  • Q6: How to deliver your wheels?
    A:We cooperate with very reliable shipping company and agent, if you dont have your own agent, we can help you and give you sug-gestions and the most economic way for shipping by sea, by train or by air, you can choose pickup wheels from the nearest port or at your shop.
  • Q7: Can you produce according to the samples?
    A:Yes, we can produce according to your samples or technical drawings.

Basic Information
  • Year Established
  • Business Type
  • Country / Region
  • Main Industry
  • Main Products
  • Enterprise Legal Person
  • Total Employees
  • Annual Output Value
  • Export Market
  • Cooperated Customers


Send your inquiry

Leave A Message

The first thing we do is meeting with our clients and talk through their goals on a future project.
During this meeting, feel free to communicate your ideas and ask lots of questions.
They are all manufactured according to the strictest international standards. Our products have received favor from both domestic and foreign markets.
They are now widely exporting to 500 countries.
Chat with Us

Send your inquiry

Choose a different language
Current language:English